Senior Process Engineer

Job Responsibilities:
 Prepared PFD, P&ID, Line List, Equipment List, Design Basis, Cause and effect, Control Philosophy.
 Performed Hydraulic Calculation.
 Sizing of Pipeline for Fire water.
 Sizing of Storage Tank, Vessel.
 Sizing of Pump (Fire Water, Submersible, Positive Displacement).
 Sizing of Sanitary Lift Station.
 Calculated Man-hour and updated Deliverables.

 Prepared PFD, P&ID, Line List & Equipment List.
 Prepared Design Basis & Process Philosophies (Operation, Vent & Depressurizing, Isolation, Shutdown, Drainage, Fire Water etc).
 Performed Mass & Heat Balance Calculation and Hydraulic Calculation.
 Performed Process Design, Sizing Circulating Pumps.
 Sizing of Pipeline for Fire water, Nitrogen and Portable Water.
 Sizing of Water Treatment Package.
 Sizing of Odor Control System.
 Sizing of Storage Tank.
 Sizing of Pump (Fire Water, Irrigation Water and Potable Water).
 Sizing of Submersible Pump (Sanitary & Borewell).
 Prepare Utility summary.
 Prepare Process Datasheet for Cartridge Filter.
 Prepare Process Datasheet for Diaphragm Pump.
 Performed Design of Vapour Recovery System.
 Participating in Waste Water Treatment – HAZOP
 Calculated Man-hour and updated Deliverables.
 Performed with Process Simulation Software HYSYS
 Performed other Calculation by using AFT FATHOM and AFT ARROW Software.

Job Responsibilities:
 Prepared PFD, P&ID , Line List & Equipment List.
 Prepared Design Basis & Process Philosophies (Operation, Shutdown, Drainage etc).
 Performed Mass & Heat Balance Calculation and Hydraulic Calculation.
 Performed Process Design, Sizing and Selection of equipments i.e. Storage Tank, Loading & Circulating
Pumps, Filters, Sump, Scraper Launcher & Receiver.
 Sizing of Pipeline for Fire water, Nitrogen and Portable Water.
 Sizing & Selection of Control Valves, Pressure Safety Valves, Flow Element and Restriction Orifice.
 Performed Design of Vapour Recovery System and Flare System.
 Prepared Technical Datasheet for equipments and instruments using and applying international standards and codes (API, NFPA, ASME, ANSI, ASTM).
 Performed with Process Simulation Software HYSYS
 Performed other Calculation by using AFT FATHOM and INSTRUCAL Software.
 Preparing reports and studies for client.
 Partiticipated in P&ID Review.

Job Responsibilities:

 Prepared PFD, P&ID , Line List & Equipment List.
 Performed Mass & Heat Balance Calculation and Hydraulic Calculation.
 Performed Process Design, Sizing and Selection of equipments i.e. Storage Tank, Pumps, Filters, Vertical & Horizontal Vessel.,
 Performed with Process Simulation Software HYSYS.
 Sizing & Selection of Control Valves, Pressure Safety Valves, Flow Element and Restriction Orifice.
 Compared & Scrutinized Process Feed Package with Process Proposal Checklist and detected errors / mistakes marked and recommended for rectification or revisions of PFD & P&ID, Equipments and Instruments Datasheets, Line & Equipments Lists, Prepared Additional Requirement List by referring Process Proposal Checklist & Design Notes.
 Prepared technical clarification list and Sizing Technical Data sheets for Equipments and Instruments and applied
International Standards & Codes viz API, NFPA, ASME, ANSI and ASTM respectively
 Preparation of Temperature Gauge & Level Gauge Datasheets.
 Performed Sizing of Heat Exchanger Datasheet by using Software HTFS.
 Performed Sizing of Flare Header by using Flarenet Software
 Scrutinized Piping Specialty (PSV, Strainer, Hose) Data sheet
 Scrutinized Storage Sphere Tank, Refrigeration Unit Package Data sheets and Loading Arm Data sheets.
 Scrutinized Metering Skid Datasheet for MBTE & Methanol and Prepared Process description documents.
 Calculated Man-hour and updated the Deliverables.
 Presentation made in all disciplines

Job Responsibilities:
 Prepared PFD, P&ID , Line List & Equipment List.
 Prepared Design Basis & Process Philosophies (Operation, Shutdown, Drainage etc).
 Performed Mass & Heat Balance Calculation and Hydraulic Calculation.
 Performed Process Design, Sizing and Selection of equipments i.e. Storage Tank, Loading & Circulating
Pumps, Filters, Cooler, Scrubber Circulation Drum, Reinjection Pump, Slop Drum, Dike Area Sump, Condensers, Scraper Launcher & Receiver, Flare KO, Drum Flare Unit, Dock Safety Unit, Detonation Arrestor.
 Sizing of Pipeline for Fire water, Foam , Storm Water, Nitrogen and Portable Water.
 Sizing & Selection of Control Valves, Pressure Safety Valves, Flow Element and Restriction Orifice.
 Performed Design of Vapour Recovery System and Flare System.
 Prepared Technical Datasheet for equipments and instruments using and applying international standards and codes (API, NFPA, ASME, ANSI, ASTM).
 Performed with Process Simulation Software HYSYS
 Performed other Calculation by using AFT FATHOM, , HTFS and INSTRUCAL Software.
 Performed Sizing of Heat Exchanger Datasheet by using Software HTFS.
 Taking reference of process licensors, such as UOP, Stone & Webster, axens etc.
 Preparing reports and studies for client.
 Preparing associated deliverables in line with scope requirements and realistic project schedule.
 Partiticipated HAZOP studies.